Simple Workbench Dogs

In this video I make some simple dogs for my workbench.  

Before I started, I wasn't sure I'd need/use them, but fancied giving it a try - and now they're installed I haven't stopped using them

I started with a scrap of oak that was around 33mm square which I'd use to make the dogs.

I picked the back left hand corner of my workbench for a few reasons - I have access to the underside of the worktop in this area, it's also in a good position to plane/sand etc, and finally it's out of the way of the main surface area of the worktop.

Making A Quick, Simple and Strong Workbench

Recently a friend of mine got in touch and asked me for help building a workbench.  He wanted something simple and strong to fit in to a space in his garage and he sent me these dimensions. 
 
So I did a drawing on SketchUp, I designed a simple frame made from basic 63mm x 38mm construction timber these are more commonly known as 3x2s, although they actually measure less than 3 by 2 inches.

Perspex Sharpening Station

In this video I use some reclaimed perspex to make a sharpening station to hold my sharpening stones/plates.

I used perspex rather than wood as I use water to lubraicate my plates and stones and I didn't want a material that would absorb the water.

I use the following products for sharpening, and as you see at the end of the video I get pretty good results with these.

Simple Panel Cutting Jig for DeWalt DW745 tablesaw

In this video I make a simple panel cutting jig for my tablesaw the DW745 using salvaged materials.

Finishing The New Workshop Layout - Workshop Re-Model Episode 8

Last in a short series about re-modelling my small workshop space.

In this video I make a simple box out of some salvaged OSB to store wood.  Simple butt joints, glued and screwed, and I added some castors to the bottom just because I had a spare set which will be useful if I ever need to move it around.

Mitre Station Support, Clamp Storage & Tool Wall - Workshop Re-Model Episode 7

In this video I make a simple unit to support material at the right hand side of my mitre station while I make cuts that also holds some of my clamps too, and I start my first of two new tool walls.
 
I used some scrap blockboard and melamine to make a simple unit mounted on castors which sits about 1cm below the height of the mitre saw’s base so that when I cut material, the offcut doesn’t fall on to the floor of the workshop.
 
I made a simple rack inside the unit to hold my F clamps by cutting some slots in to another piece

New Mitre Station (part 3 of 3) - Workshop Re-Model Episode 6

In part 3 I begin by making a new fence for the mitresaw.  Originally I was going to make one using wood, but while I was in my local DIY shop I stumbled upon some lengths of aluminium angle which were relatively inexpensive and it occurred to me that it would be worth using that instead as it is perfectly straight.  
 
I decided to fit this not only to the worktop of the mitrestation, but also to the saw itself to replace the existing mitre saw fence.

The New Mitre Station (part 2 of 3) - Workshop Re-Model Episode 5

In part 2 of the mitre station build, I started by fitting some structural supports/spacers to the mitresaw stand.  These would make the structure more rigid and also ensure that the space between the two panels would be evenly spaced so that I could later fit a drawer in the space.
 
Next I made a hood for the mitresaw to help contain any dust that my shop vac doesn’t catch.  I used some salvaged blockboard to make the hood, and another piece of white 1 inch thick melamine for the top.

The New Mitre Station (part 1 of 3) - Workshop Re-Model Episode 4

In this video I start making a new mitre station for my workshop to create space in the corner for a wood storage bin, and also to make it a little slimmer so there would be more walkway space.  
 
I dismantled my old mitre station and re-used most of the material for the new one.  
 
I started by screwing a horizontal support piece to the uprights of the workshop walls.

Mobile Tablesaw Stand for DeWalt DW745 (part 2 of 2) - Workshop Re-Model Episode 3

In this video I make a back panel for the stand out of some low grade packaging plywood.  I did this mainly to stop some of the dust getting in to the bottom section where the shop vac and jigs will be stored, but it will also add rigidity to the stand.

Next I fitted the shop vac hose, using a hole saw drill bit.

I cut some pieces of poplar in to 10mm strips, cut them to length and glued and nailed them to the front edges of the stand mainly to hide the plywood edges for aesthetics.

Pages